Manual.ly Logo

sera UVC-Xtreme 800 Bruksanvisning

0,0 · 0 Betyg

PDF-manual · 90 Sidor

Svenska

M: GO-GEM-FL-25
sida

/ 90

Loading...
781d6a9054693a344975a2f7322d15035812 page 11
17
Maintenance and care
Cleaning (every 4 – 12 weeks)
Over time and depending on biological load, food amount and aquarium
volume, mechanical and biological lter media get clogged more or less
quickly. Due to increasing sedimentation, the turnover through the lter
is reduced.
For cleaning, please rst pull the barrel plug from the lter head (6.5)
and then close the valves by turning the taps by 90° perpendicular to
the ow direction (6.4).
Now open the 4 holder clips (8.1 – 8.2). This leads to pressure release,
and you can now unscrew the valves from the lter head without water
running out (7.6). Now take the lter head off and lay it aside, or put it
back if you wish to carry it to a sink or the location where you wish to
clean the lter media.
You can now take the lter media baskets (1.34) out from above and
wash out the lter materials. It is best to use aquarium water for wash-
ing them out since this, unlike tap water, does not endanger the lter
bacteria. Never replace the lter material entirely but always retain used
lter material. By doing so, the lter bacteria will then spread over the
entire lter material again. Newly setup lters can also be activated by
using used lter material.
Maintenance of the running unit (every 3 – 9 months)
Please check the bottom side of the lter head whether the running unit
can move freely. To do so, please remove the two 90° elbows and the
pump chamber cover. Turn the rotor with your ngers. You should be able
to turn it without suspicious resistance. Rinse the openings thoroughly
with a water beam, depending on deposits and biolm, and re-assemble
the lter (4.1 – 4.7).
Possible problem sources and solution
Problem Possible cause Possible solution
E1 Suction pump does not ll up the
lter
E1.1 Are “IN” and “OUT” valves/hoses mixed up?
Check if bubbles are coming out of the intake strainer while suction
pump is in operation.
Yes, switch “IN” and “OUT” valves/hoses.
Make sure that the valve marking corresponds with the valve connector marking
(7.3).
No, see item E1.2
E1.2 Are “IN”/“OUT” valves still closed? Yes, open taps (6.4) of the “IN”/“OUT” valves.
No, see item E1.3
E1.3 Did you forget to insert the lter head seal (1.31)?
Yes, insert the lter head seal.
No, see item E1.4
E1.4
Are hoses laid out in a loop?
Yes, lay the hoses out without loops, shorten them if applicable.
No, see item E1.5
E1.5 Is the lter in operation for the rst time? Yes, ll the lter canister with water by two thirds. Then press “S”.
No, see item E1.6
E1.6
Dirt particles in the outlet valve?
Yes, remove the valve, clean it, and re-assemble.
No, see item E1.7
E1.7 Too low water level of the tank (e.g. terrapin tank)? Yes, press “S” button (2) repeatedly after suction is completed, or raise the
performance setting by pressing the “+” button. The setting can be adjusted as
desired once the air trapped inside the lter has escaped.
No, see item E1.8
E1.8 Is the spray bar too deep underneath the water surface? Yes, install the spray bar parallel to water surface, 15 cm (6 in.) underneath it at the
maximum (7.1).
No, see item E5, or please contact your retailer.
E2 Pump does not work E2.1 Power supply interrupted? Check mains and 5.5 mm (0.2 in.) barrel
plugs.
Yes, connect to power supply.
No, see item E2.2
E2.2 Are the valves still closed? Yes, open valve taps (6.4).
No, see item E2.3
E2.3 Is the rst LED ashing (green)? Yes, exit standby mode by pressing the “+” button (2).
No, see item E2.4
E2.4 Are the rst and second green LEDs ashing at the same time? Yes,
– disconnect the lter from the mains supply and reconnect it; or
– disconnect the lter from the mains supply, open the lter head (8.1 – 8.2). Clean
the lter head, in particular the rotor (3), so the rotor can rotate freely.
No, see item E2.5
E2.5 Too much air in lter? Yes, see item E5 of the chart.
No, please contact your retailer.
E3 Pump performance has strongly
decreased
E3.1 Are the valve taps (6.4) not in the correct “OPEN” position? Yes, open the valve taps properly so both handles are parallel to the longitudinal axis
of the valves.
No, see item E3.2
E3.2 Hoses bent, polluted or covered with biolm layers? Is there an
obstacle in the tubing?
Yes, clean/brush hoses and tubing, remove biolm inside the hoses by means of a
hose brush. Remove obstacles in the tubing.
No, see item E3.3
E3.3 Intake strainer or outlet clogged? Yes, clean strainer or outlet and remove coarse dirt.
No, see item E3.4
E3.4 Too much air trapped inside the lter? Yes, press “S” key (2) until pump works properly, repeat as required.
No, see item E3.5
E3.5 Too many devices connected to lter? Yes, prelters, T pieces, UV-C lamps etc. additionally connected to the intake or
outlet reduce the ow rate. The UVC-Xtreme lter already contains a suitable UV-C
lamp.
No, see item E3.6
Replacing the UV-C lamp (every 1 – 1.5 years)
Should the blue LED indicator lamp stay off, or if the UV-C lamp is
1.5 years old at the maximum, it needs to be replaced. First switch off
the lter head for replacing the lamp. Pull the barrel plug from the lter
head (6.5). Then you can disconnect the head from the lter (8.1 – 8.2).
Unscrew the union nut of the UV-C intake nozzle after having removed
the magnetic contact (1.18, 9.1/9.2), then pull the two 90° elbows at-
tached to the nozzles (9.3).
Now the union nut of the UV-C nozzle can be unscrewed (9.4). Pull the
nozzle off upwards. The quartz glass cylinder is located underneath.
It can now be pulled off, granting access to the lamp (9.5). The UV-C
lamp can be removed from the socket by pulling it gently. It can now be
replaced with a suitable replacement lamp. Then re-assemble the lter
in reverse order (9.6 – 9.1).
Switch-off protection: UV-C radiation is dangerous. Irradiation of
eyes and skin must be strictly avoided. The lters are constructed
according to latest safety standards in a way that a magnetic switch
switches off the UV-C lamp as soon as the lamp casing is opened.
Prior to every maintenance measure, the magnetic contact should
be removed rst before removing the two clickable 90° elbows, as
this will prevent possible eye or skin damage caused by UV-C radia-
tion being released from the now opened connection of the two 90°
elbows at the UV-C tube, in case disconnecting the device from the
mains supply was forgotten.
000000-00_sera UVC Xtreme 800_1200_INT_GBI.indd 17 07.09.2017 08:12:35

Chatta med din sera UVC-Xtreme 800-manual med hjälp av AI

Få omedelbara AI-svar från din sera UVC-Xtreme 800-manual

Fråga vad som helst om sera UVC-Xtreme 800. Svaren kommer från denna bruksanvisning, med de sidor de bygger på.

UVC-Xtreme 800 Underhallsschema

Paminn mig nar underhall ska utforas
Varje 4:e vecka
Rengör filtermedia

Skölj mekaniskt och biologiskt filtermaterial med akvatiskt vatten för att bevara bakterier. Byt inte ut allt material på en gång.

Visa i manualen (sida 17)
Varje 6:e månad
Underhåll driftenhet

Kontrollera om rotorn roterar fritt för hand och skölj öppningar med ett vattenstråle för att ta bort biofilm eller avlagringar.

Visa i manualen (sida 17)
Varje 9:e månad
Byt UV-C-lampa

Byt amalgamlampan efter maximalt 1,5 år för att säkerställa full funktion, även om indikatorlampan fortfarande är tänd.

Visa i manualen (sida 17)

Kostnadsfria underhallspaminnelser

Anpassat efter ditt inkopsdatum. Alltid kostnadsfritt, avsluta prenumerationen nar som helst.

Genom att skicka in godkanner du integritetspolicyn. Avsluta prenumerationen med ett klick i valfritt e-postmeddelande.
M: QW-35-FL

Ställ en Fråga

0/1000

Rekommenderar du UVC-Xtreme 800?

Ja Nej

Vanliga frågor

A

UV-C-enheten är avsedd för att reducera patogener och svävalger genom att bestråla vatten efter att det passerat filtermediet. Systemet är inte utformat för att sterilisera ett akvarium, och nyttiga bakterier på mediet förblir i stort sett opåverkade.

Är detta svar till hjälp?

A

Börja med en medelhög prestandanivå och justera baserat på din akvariestorlek och alg- eller patogentryck. Lägre cirkulation ökar tiden vattnet tillbringar i UV-C-enheten, vilket kan förbättra reduktionen. Om luft är instängd eller flödet verkar svagt, öka kortvarigt.

Är detta svar till hjälp?

A

Under första körningen kan instängd luft nå rotorområdet och öka ljudnivån. Använd sugpumpsfunktionen för att avlägsna luft under filterhuvudet. Efter några minuter minskar ljudet vanligtvis när luftflödet stabiliserats.

Är detta svar till hjälp?

A

Mekaniskt och biologiskt filtermedia bör kontrolleras och rengöras ungefär var 4:e till 12:e vecka, beroende på bioload, utfodring och akvarievolym. Om cirkulationen minskar, rengör endast det som behövs och undvik att byta ut allt media samtidigt.

Är detta svar till hjälp?

A

Lampans livslängd beror på omkopplingscykler, men servicevägledningen indikerar ungefär 1 till 2 år. Lampan bör bytas ut efter cirka 1,5 år för att säkerställa full prestanda, särskilt om UV-C-indikatorn inte längre visar normal drift.

Är detta svar till hjälp?

A

Kontrollera att IN/OUT-ventilerna är helt öppna, att slangarna inte är veckade och att mediekorgarna inte är igensatta. Kontrollera också att rotorn kan röra sig fritt och att det inte finns för mycket instängd luft. Om problemet kvarstår, inspektera utloppsvägen och kontakta en återförsäljare.

Är detta svar till hjälp?

M: GO-GEM-FL-25

Fördelar och Nackdelar

Fördelar

  • Integrerad omkopplingsbar UV-C med amalgamlampa för stabiliserad prestanda och högre emissionspotential
  • Lågspännings, tyst motor med flera inställningar för att justera flöde, energiförbrukning och UV-exponeringstid
  • Elektrisk sugpump hjälper till att avlägsna instängd luft efter installation eller underhåll för tyst drift
  • 360-graders roterbara ventiler och komplett anslutningssats förenklar installation och hantering
  • Optimerad flödesväg för mediekorgar stödjer mekanisk och biologisk filtrering med långa serviceintervall
VS

Nackdelar

  • Kräver noggrann hantering av UV-C-säkerhet och endast originalamalgamersättningslampor
  • Prestandan sjunker om filtermedia eller slangar täpps igen eller om luftflödet blockeras
  • Korrekt tätning, upprätt placering och rätt IN/OUT-anslutningar är avgörande för att förhindra läckage och luftproblem
  • Serviceuppgifter (rotor- och UV-C-underhåll) involverar demontering som bör utföras försiktigt
M: GO-GEM-FL-25

Produkt Specifikation

Typ

Externt filter med UV-C-klarerare

Flödesvolym

840 l/h

Akvariestorlek

100-800 l

Strömförbrukning

24 W

Funktioner

UV-C-lampa, inkl. inlopps-/utloppssats

M: GO-GEM-FL-25

Produkt Beskrivning

sera Professional UVC-Xtreme 800 Externt Filter

sera Professional UVC-Xtreme 800 Externt Filter kombinerar UV-C-stöd och elektronisk kontroll i ett effektivt, tyst externt filtreringssystem byggt för sötvattensakvarier. Designat för flexibel installation, använder det en modern lågspänningsmotor med flera prestandanivåer, vilket låter dig anpassa vattencirkulationen till akvariets storlek, bioload och önskad UV-C-behandlingsintensitet. I energisparläge kan det köras med låg effekt samtidigt som det levererar stark cirkulation vid behov.

Vad som utmärker Xtreme-serien är den integrerade UV-C-enheten som kan växlas från kontrollpanelen. UV-C-amalgamlampan ger stabiliserad effekt inom sitt driftstemperaturområde och är avsedd att reducera patogener och svävalger mer effektivt än många konventionella UV-C-lampor. Istället för att sikta på verklig sterilisering, fokuserar systemet på patogenreduktion samtidigt som nyttiga filterbakterier som primärt lever i filtermediet bevaras.

Vatten flödar genom optimerade mediekorgar från topp till botten. En räfflad svamp hjälper till att fånga grova partiklar, medan fina och biologiska medietyper (till exempel keramiska biomedia) stödjer mekanisk och biofiltrering. Efter att vattnet passerat mediet dras det mekaniskt och biologiskt förbehandlade vattnet till UV-C-zonen, för att sedan återföras till akvariet via OUT-ventilen. Systemet inkluderar även en elektrisk sugpump som hjälper till att avlägsna instängd luft efter installation eller underhåll, vilket stöder tyst och pålitlig drift.

För säker och korrekt användning, se sera Professional UVC-Xtreme 800 Externt Filter Manual vid installation av ballast, placering av filtret och hantering av UV-C-komponenter. Enheten är avsedd för inomhusbruk, kräver tillräckligt vattenflöde och inkluderar säkerhetsåtgärder för att förhindra UV-C-exponering under underhåll.

Huvudresultat

  • UV-C-aktiverad extern filtrering med omkopplingsbar kontroll för patogen- och svävalgreduktion
  • Flera motorprestandanivåer för att balansera cirkulation, UV-exponeringstid och energiförbrukning
  • Integrerad luftarbetningsrutin för smidigare uppstarter efter rengöring
  • Optimerad flödesväg och mediekorgar för att stödja långa serviceintervall
  • Enkel 360-graders ventilorientering och medföljande anslutningssats för flexibel installation

Anmärkningar

  • Föredra partiell medierengöring och återanvändning av etablerade medier för att skydda nyttiga bakterier.
  • UV-C-amalgamlampor byts vanligtvis ut enligt en servicescykel (cirka 1 till 2 år beroende på omkoppling), enligt enhetens riktlinjer.
  • Säkerställ korrekt tätning, upprätt placering och korrekta IN/OUT-anslutningar för att bibehålla flöde och effektivitet.
M: GO-GEM-FL-25

© Copyright 2026 Manual.ly